Skip to main content
Job description

Low-Voltage Electrician (Security Specialty) Job Description

Physical Security

Installs the cabling infrastructure that security systems depend on. Runs pathways and conduit, pulls and dresses structured cabling, roughs in readers, cameras, door hardware and detection devices, and distributes power and PoE to them. Makes terminations that satisfy both the manufacturer requirements and the limited-energy sections of the electrical code. Tests, labels and documents what was installed so the integration technician can configure a system that actually works.

15essential duties
8 / 7required / preferred qualifications
6credentials, each with who verifies it
Take this away as a Word document The same description, formatted for a personnel file, with an acknowledgement signature block at the end. The first download asks for your name, company, work email and phone; after that every document here downloads without a form.
Download .docx

What this seat pays

$42,640 to $108,510 BLS 10th to 90th percentile

Federal figures: BLS Occupational Employment and Wage Statistics, May 2025, national, SOC 47-2111. The range is the 10th to 90th percentile and the median is $63,190. It is not adjusted for experience or region, and it is not a My Trade Talent band.

Pay, location and the date prepared are blank in the Word version on purpose. They depend on your market and your margins, and a template that guesses at them is worse than one that leaves them to you. The figure above is here so the guess is at least anchored.

The seat

Reports toInstallation Supervisor or Field Operations Manager
Direct reportsNone (may direct an apprentice or helper)
FLSA statusNon-exempt — confirm with counsel
TradePhysical Security
Pay band$42,640 to $108,510 — BLS 10th to 90th percentile

Where the role goes next. Low-voltage electricians move to lead, foreman, or across into systems technician and integration work.

Essential duties (15)

  • Lays out and installs pathways for low-voltage work: EMT and flexible conduit, surface raceway, cable tray, sleeves and core-drilled penetrations, sized and routed to the drawings and the device locations.
  • Pulls, supports and dresses structured cabling — Cat 6 and 6A, composite camera cable, 18/2 and 22/4 shielded, fiber where specified — on J-hooks or tray at the spacing the code and the manufacturer require, with no kinks, overcinched ties or exceeded bend radius.
  • Installs plenum-rated cable in air-handling spaces and firestops every rated penetration with a listed system, then documents what system was used where.
  • Roughs in device locations for card readers, request-to-exit devices, door position switches, electric strikes, mag locks, cameras, intercoms, duress buttons, glass breaks and motion detectors, including back boxes, mounting plates and pigtails.
  • Runs and distributes power: locates and mounts power supplies and PoE injectors, sizes conductors for voltage drop over the run, installs and dates standby batteries, and verifies polarity and voltage at the device before energizing.
  • Terminates copper to T568B on jacks and patch panels, punches down 110 blocks, dresses and labels patch fields, and makes reader and lock terminations to the Wiegand or OSDP wiring the controller expects.
  • Tests and certifies permanent links with a certifying tester, saves the test results to the job file, and reterminates any link that fails rather than passing it along.
  • Labels every cable, jack, panel port, power supply and device to the project labeling scheme and keeps the label schedule current as the job changes.
  • Terminates and bonds shields, grounds racks and enclosures, and keeps limited-energy conductors separated from line-voltage circuits per the code sections that apply to Class 2 and Class 3 work.
  • Works from ladders, scissor lifts and boom lifts in finished and unfinished spaces, and protects finished surfaces, ceiling tile and flooring while doing it.
  • Redlines the drawings as installed — moved devices, changed routes, added pulls — and turns the redlines in so the as-builts and the integrator are working from reality.
  • Coordinates with the door hardware installer, the general contractor and the electrician on door prep, power whips and ceiling access so rough-in is not blocked or buried.
  • Writes service tickets and daily field reports describing what was done, what is left and what is waiting on someone else, and submits timesheets by the payroll cutoff.
  • Keeps the work area, gang box and truck stock organized, returns unused material with the reel footage recorded, and cleans up cable scrap, ceiling debris and core-drill slurry each day.
  • Accompanies the inspector on rough-in and final inspections for limited-energy work and corrects anything cited before leaving the site.

Qualifications

Required
  • Two or more years installing commercial low-voltage or electronic security systems, including structured cabling and device rough-in
  • State low-voltage, alarm or electronic security installer license, registration or company-held license endorsement where the state or municipality requires one for this work
  • Working knowledge of the limited-energy articles of the NEC (Class 2 and Class 3 circuits, communications and optical fiber cabling) and of plenum and firestopping requirements
  • Able to read and work from electrical, architectural and reflected ceiling drawings, door schedules and riser diagrams
  • Valid driver license and a motor vehicle record that the company insurance carrier will accept
  • Able to climb ladders, work from lifts, work above shoulder height and lift and carry up to 50 pounds for most of a shift
  • Passes the criminal background check and drug screen that security clients and the industry require for site access
  • Owns and uses hand tools and basic termination tools, and arrives with them
Preferred
  • BICSI Installer 1 or Installer 2 Copper credential
  • Experience roughing in for a named access control platform such as Mercury-based controllers, LenelS2, Genetec or Software House
  • Fiber splicing and termination experience, including fusion splicing and OTDR testing
  • Conduit bending and electrical rough-in experience on commercial projects
  • Experience on occupied healthcare, education or data center sites with infection control, badging and escort requirements
  • Aerial lift and scaffold operator cards already in hand
  • Experience with camera aiming and focus assistance during commissioning

The line between these two columns is the one that costs you candidates. Everything in the preferred column that gets written into a posting as a requirement removes people who could do the job, and in a trade with a shortage that is a self-inflicted wound.

Credentials, and who verifies them

CredentialStatusVerify with
State or municipal low-voltage, alarm or electronic security installer license or registrationWhere the state requires itState or city licensing board online lookup, with a copy in the employee file and the renewal date tracked
Driver license with insurable motor vehicle recordRequiredHR, with an MVR pulled through the company insurance carrier at hire and annually
OSHA 10-hour or 30-hour construction trainingRequiredTraining provider card or the DOL card, verified by the safety manager
Aerial lift and scissor lift operator trainingRequiredInternal or third-party trainer records held by the safety manager
BICSI Installer 1 or 2PreferredBICSI credential verification and the certificate on file
Manufacturer installer certifications for the platforms the company installsPreferredManufacturer partner portal transcript, kept with the technician record

Verify before an offer rather than after. A credential taken on trust at offer is the most expensive line on this page. We track physical security licensing in 39 states; which of them applies depends on where the work is, not where the company is.

Physical demands

ActivityFrequency
Fine hand dexterity for terminating, punching down and setting small devicesConstant (over 2/3 of shift)
Standing and walking on construction floors, uneven decking and finished slabConstant (over 2/3 of shift)
Distinguishing conductor and pair colors for terminationsConstant (over 2/3 of shift)
Climbing and working from ladders, scissor lifts and boom liftsFrequent (1/3 to 2/3 of shift)
Reaching and working above shoulder height in ceilings and on wallsFrequent (1/3 to 2/3 of shift)
Kneeling, crouching and bending to work in back boxes, floor cores and equipment racksFrequent (1/3 to 2/3 of shift)
Lifting and carrying up to 50 pounds (cable reels, power supplies, tool bags, lift batteries)Frequent (1/3 to 2/3 of shift)
Driving a company vehicle between sites and the shopFrequent (1/3 to 2/3 of shift)
Working in attics, above hard-lid ceilings and in crawlspaces with limited headroomOccasional (under 1/3 of shift)
Wearing a filtering facepiece respirator in dusty plenum, attic or demolition areasOccasional (under 1/3 of shift)
Operating hammer drills and core drills with vibration and overhead forceOccasional (under 1/3 of shift)
Permit-required confined space entry (vaults, manholes, pipe chases)Rarely

This is the section a reasonable accommodation decision actually turns on, which is why it is role specific rather than copied across a trade. An estimator sits and walks sites; a screed operator stands beside hot asphalt all day.

Work environment

Commercial construction sites and occupied buildings: new construction before the ceiling closes, tenant improvements at night, and live facilities where the existing system stays armed. Conditions include dust, noise, unconditioned space, open ceilings and active trades overhead. Hazards are falls from ladders and lifts, cuts from cable and sheet metal, electrical contact in shared enclosures, and overhead loads. Some evening, weekend and shutdown work; occasional overnight travel to out-of-area jobs.

Tools and equipment

The company provides ladders, lifts, power tools, core drills, fish tape, cable reels and the certifying cable tester, plus a company vehicle, PPE, a label printer and all installation material. The technician owns and maintains a standard hand tool set, including strippers, punch-down and crimp tools, a multimeter, knives, drivers, a tape and personal work boots.

How performance is measured

MeasureWhat it captures
First-pass certification rateShare of permanent links that pass certification testing without retermination
Rough-in ready for trim on scheduleDevice locations roughed in, powered and ready for trim by the date on the schedule
Punch items returned by the integrator or inspectorCount of items sent back per job after the technician called an area complete
Labeling and as-built accuracyField labels and submitted redlines match what the record drawings and the integrator find
Material and reel accountabilityCable footage, device counts and returned stock reconciled against the estimate
Daily paperwork on timeField reports and timesheets submitted by the cutoff every working day
Limited-energy inspection resultsRough-in and final inspections passed without correction notices

These are the same measures the annual review for this role is built on, so the document you hire against and the document you rate against are measuring one thing.

Reading a resume for this seat

What separates a strong Low-Voltage Electrician (Security Specialty) from a plausible one, on paper and in the first ten minutes of a call:

  • Licensing stated accurately for the state, because low-voltage licensure varies and matters
  • Terminations and testing described with the standard used, not just "ran the cable"
  • Understands where limited-energy work still falls under the electrical code

Screen for it: 3 questions and what a strong answer contains

A job description tells you what you need. These tell you whether the person in front of you has it. Each one comes with what a strong answer contains, because an interviewer who does not know that is persuaded by fluency, which is exactly what the question was supposed to see past.

What licence do you hold for low-voltage work in this state and what does it cover?

What a strong answer contains

Names the actual licence or registration rather than saying they are licensed, and knows what it permits and what it does not - which usually stops well short of line voltage work. Knows whether their state licenses alarm, security or low-voltage work separately, whether a company licence covers them or they hold it personally, and what continuing education or renewal it carries. Knows which work requires an electrician instead.

Follow up with: What work on a job site do you have to hand to a licensed electrician?

How do you certify a structured cabling run and what do you do with a failed test?

What a strong answer contains

Tests to the category and standard with a certifier rather than a continuity tester, and knows the difference, because a wire map proves nothing about performance. Saves the results per run with the labels matching the as-built. On a failure, reads which parameter failed and at what distance, because that points at the fault - a termination, a kink, a run too long, or an untwist at the jack - rather than re-terminating blindly.

Follow up with: A run fails NEXT. Where do you look first?

Where does your PoE budget run out on a switch and how do you plan for it?

What a strong answer contains

Knows the switch has a total power budget separate from the per-port maximum, that the devices' draw at startup and at full load differs from their idle draw, and that heaters, infrared and pan-tilt cameras spike. Adds up the real worst-case load rather than the nameplate average, allows for cable loss over distance, and leaves headroom for growth. Checks the standard the devices need rather than assuming they all take the same.

Follow up with: Why can a switch pass its budget at night when it was fine in the day?

The mistake this seat invites

Assuming a licensed electrician can drop straight in. The code sections, the testing standards and the licensure are a different specialty, and the reverse assumption is just as wrong.

How long this takes to fill

We publish no physical security median of our own yet, so this is the all-trades figure: My Trade Talent's median commercial trades hire took 21 days across 94 searches closed in 2026 year to date, counted as calendar days from our first contact with the candidate to the hire.

Worth writing on the requisition before you post it. The cost of the vacancy runs from the day the seat empties, not from the day you start looking, and the calculator will put a number on it for your billing rate.

Questions employers ask about this role

What does a Low-Voltage Electrician (Security Specialty) do?

Installs the cabling infrastructure that security systems depend on. Runs pathways and conduit, pulls and dresses structured cabling, roughs in readers, cameras, door hardware and detection devices, and distributes power and PoE to them. Makes terminations that satisfy both the manufacturer requirements and the limited-energy sections of the electrical code. Tests, labels and documents what was installed so the integration technician can configure a system that actually works. The full description below lists 15 essential duties in trade terms, with physical demands and frequencies.

What qualifications does a Low-Voltage Electrician (Security Specialty) need?

8 requirements are written as non-negotiable for this seat. The first 3: Two or more years installing commercial low-voltage or electronic security systems, including structured cabling and device rough-in; State low-voltage, alarm or electronic security installer license, registration or company-held license endorsement where the state or municipality requires one for this work; Working knowledge of the limited-energy articles of the NEC (Class 2 and Class 3 circuits, communications and optical fiber cabling) and of plenum and firestopping requirements. A further 7 qualifications are preferred rather than required, which is the distinction that decides whether a good candidate gets screened out by your own posting.

What credentials should I verify before making an offer to a Low-Voltage Electrician (Security Specialty)?

4 credentials on this role are either required outright or required where the state requires it: State or municipal low-voltage, Driver license with insurable motor vehicle record, OSHA 10-hour or 30-hour construction training and Aerial lift and scissor lift operator training. Each one has a named place to verify it in the table below. Verify before the offer rather than after; a credential taken on trust at offer is the most expensive line in a job description.

Is a Low-Voltage Electrician (Security Specialty) exempt or non-exempt?

Non-exempt — confirm with counsel. FLSA status turns on the duties actually performed rather than the job title, and the duties for this seat are listed below so a classification decision has something to rest on. We are not lawyers and the note here is a starting point for counsel, not a determination.

What should a Low-Voltage Electrician (Security Specialty) be paid?

$42,640 to $108,510. Federal figures: BLS Occupational Employment and Wage Statistics, May 2025, national, SOC 47-2111. The range is the 10th to 90th percentile and the median is $63,190. It is not adjusted for experience or region, and it is not a My Trade Talent band.

How long does it take to hire a Low-Voltage Electrician (Security Specialty)?

We publish no physical security median of our own yet, so this is the all-trades figure: My Trade Talent's median commercial trades hire took 21 days across 94 searches closed in 2026 year to date, counted as calendar days from our first contact with the candidate to the hire.

What is the most common hiring mistake in this seat?

Assuming a licensed electrician can drop straight in. The code sections, the testing standards and the licensure are a different specialty, and the reverse assumption is just as wrong.

Trade Talk A monthly hiring brief for commercial trades employers

What changed in your trade this month, and what to do about it.

One email a month, and only one. We write a separate issue for every trade we recruit in, so you get yours - not a round-up with your trade buried in paragraph nine. Every issue is written for the person actually doing the hiring.

  • Where wages moved in your trade, by market, and what that does to your next offer
  • How long roles like yours are taking to fill, and where it is getting worse
  • Interview and screening tactics that are landing candidates this month
  • What contractors competing for the same people are doing differently

Built on federal wage data, our own closed searches, and what we hear on the desk every week. Written for employers, not candidates. No pitch, no filler, one click to leave.

Pick your trade. That is the one issue you get, once a month.

One email a month. Your trade and your address, nothing else - we do not sell either, and you can unsubscribe from the bottom of any issue. Read this month's issue for your trade first →