HVAC Install Technician (Commercial) Job Description
HVAC & Mechanical
Sets and connects commercial HVAC equipment on new construction and replacement projects: rooftop units, split systems, VRF branch controllers, ductwork and refrigerant piping. The work is production against a schedule, and the technician is expected to hold rate without cutting corners. The quality of the brazing, the hanger spacing and the condensate detailing decides whether the service department inherits a problem on the unit two years later.
What this seat pays
My Trade Talent mid-experience band, built from our own engagement history. Experience and region move it; the salary calculator applies both.
Pay, location and the date prepared are blank in the Word version on purpose. They depend on your market and your margins, and a template that guesses at them is worse than one that leaves them to you. The figure above is here so the guess is at least anchored.
The seat
| Reports to | Install Foreman |
| Direct reports | None (may direct an apprentice or helper) |
| FLSA status | Non-exempt — confirm with counsel |
| Trade | HVAC & Mechanical |
| Pay band | $52,000 to $80,000 — My Trade Talent band |
Where the role goes next. Install technicians progress to install foreman and then superintendent, or move into service once they want the diagnostic side.
Essential duties (15)
- Rig and set rooftop units, air handlers and condensing units using cranes, forklifts or hoists, including curb adapter fit-up and vibration isolation.
- Braze refrigerant line sets under nitrogen purge, pressure test, evacuate to a documented micron level and charge by weight or by superheat and subcooling per the manufacturer's data.
- Install and support sheet metal ductwork, flex connections, dampers and diffusers to SMACNA standards, sealing joints and seams to the seal class the specification calls for.
- Run and support refrigerant piping, condensate drains with correct trapping and slope, and hydronic piping where the job includes coils or fan coil units.
- Install VRF branch controllers, headers and refnet joints to the manufacturer's piping diagram, keeping line length and lift within published limits.
- Pull line voltage and control wiring in conduit or MC as the job calls for, terminate at disconnects, starters and unit control boards, and label every circuit.
- Set hangers, seismic restraints and roof supports at the spacing the specification and local code require, and coordinate penetrations with the roofing and structural trades.
- Start up equipment, record charge, amp draw, static pressure and airflow on the start-up sheet, and flag any unit that will not hold the design condition.
- Work from mechanical drawings, equipment submittals and the install schedule, and raise field conflicts before building something that has to be torn out.
- Lay out equipment and duct runs from dimensioned drawings with a tape, laser and level rather than eyeballing to existing construction.
- Keep a running material list and tell the foreman what the crew needs for tomorrow before the end of today's shift.
- Turn in timesheets coded to the correct job and cost code daily, and write down extra work directed in the field so it can be captured as a change order.
- Clean the work area and remove packaging, scrap metal and empty refrigerant cylinders at the end of each shift, and leave mechanical rooms broom clean at handover.
- Complete punch list items from the engineer, commissioning agent or general contractor and verify each one is accepted before leaving the site.
- Hand over start-up documentation, warranty registrations and as-built markups to the project manager at closeout.
Qualifications
- Three or more years installing commercial HVAC equipment, not residential changeouts only.
- EPA Section 608 Universal certification.
- Able to braze copper to copper and copper to brass joints that pass a nitrogen pressure test without rework.
- Able to read mechanical drawings, equipment schedules and submittals and work from them without being walked through them.
- Valid driver's license and a driving record that qualifies for the company's insurance.
- Able to lift 50 pounds repeatedly, work from ladders and lifts, and work on roofs in summer heat and winter cold.
- OSHA 10 within 30 days of hire, or willingness to obtain it.
- Own a full set of hand tools and a working multimeter.
- Manufacturer factory training on VRF systems from Daikin, Mitsubishi, LG or Samsung.
- Completion of a four or five year HVAC apprenticeship or an equivalent trade school program.
- Aerial lift, scissor lift and forklift operator cards.
- OSHA 30 construction.
- Experience on projects under a general contractor with daily huddles, badging and an electronic punch list system such as Procore.
- NATE certification in air conditioning installation.
- Rigging and signalperson training.
The line between these two columns is the one that costs you candidates. Everything in the preferred column that gets written into a posting as a requirement removes people who could do the job, and in a trade with a shortage that is a self-inflicted wound.
Credentials, and who verifies them
| Credential | Status | Verify with |
|---|---|---|
| EPA Section 608 Universal | Required | Certifying organization card, copy in the personnel file |
| State or local HVAC journeyman or mechanical license | Where the state requires it | State licensing board license lookup |
| OSHA 10 or OSHA 30 construction | Required | Training provider completion card and DOL card number |
| Aerial and scissor lift operator certification | Preferred | Training provider record, re-verified every three years |
| Forklift operator certification | Preferred | Employer-conducted evaluation under OSHA 1910.178 |
| Valid driver's license | Required | Motor vehicle record run through the company insurer |
Verify before an offer rather than after. A credential taken on trust at offer is the most expensive line on this page. We track HVAC & mechanical licensing in 38 states; which of them applies depends on where the work is, not where the company is.
Physical demands
| Activity | Frequency |
|---|---|
| Standing and walking on uneven surfaces, roofs and unfinished slab | Constant (over 2/3 of shift) |
| Lifting and carrying up to 50 pounds | Frequent (1/3 to 2/3 of shift) |
| Team lifting or rigging loads over 50 pounds | Occasional (under 1/3 of shift) |
| Climbing ladders and working from scissor or boom lifts | Frequent (1/3 to 2/3 of shift) |
| Working above six feet, including roof edge work in fall protection | Frequent (1/3 to 2/3 of shift) |
| Kneeling, crouching and crawling in ceiling spaces and mechanical rooms | Frequent (1/3 to 2/3 of shift) |
| Reaching overhead to hang duct, pipe and equipment supports | Frequent (1/3 to 2/3 of shift) |
| Gripping and operating hand and power tools, including torch work | Constant (over 2/3 of shift) |
| Exposure to outdoor heat, cold and wind on rooftops | Frequent (1/3 to 2/3 of shift) |
| Working in confined or restricted spaces such as plenums and crawl spaces | Occasional (under 1/3 of shift) |
| Driving a company truck between the jobsite and the supply house | Occasional (under 1/3 of shift) |
| Sitting at a desk for paperwork or classroom training | Rarely |
This is the section a reasonable accommodation decision actually turns on, which is why it is role specific rather than copied across a trade. An estimator sits and walks sites; a screed operator stands beside hot asphalt all day.
Work environment
Work happens on active construction sites and in occupied commercial buildings: rooftops, mechanical rooms, above ceilings, and in parking lots staging equipment. Conditions include summer roof heat, winter wind, dust, noise above 85 decibels near running equipment, and open floor and roof penetrations. Hazards include energized electrical, torch and hot work, compressed gases, refrigerant, falls from height and overhead crane picks. Hard hat, safety glasses, gloves, high visibility clothing and steel toe boots are required at all times.
Tools and equipment
The company provides the truck or van, ladders, lifts, gauges, recovery machines, micron gauges, torch sets, nitrogen regulators, power tools, duct tools, fall protection harnesses and all PPE other than boots. The technician is expected to own a full set of hand tools, a multimeter, a tape, a torpedo level and steel toe work boots.
How performance is measured
| Measure | What it captures |
|---|---|
| Installed labor hours against estimated hours by cost code | Whether the technician holds the rate the job was sold at |
| Rework and callback hours traced to the technician's installs | Brazing leaks, miswired controls, bad condensate and loose hangers found after handover |
| Start-up sheets complete and submitted on the first pass | Whether the documentation closes without the project manager chasing it |
| Punch list items per unit installed | How much of the work the commissioning agent or general contractor sends back |
| Safety observations and recordable incidents | Hot work permits, tie-off compliance and lift inspections on the technician's work |
| Timesheet and cost code accuracy | Hours coded to the right job and extra work captured the same day |
| Material waste and tool loss on assigned jobs | Scrap copper and sheet metal, lost tools and unreturned cylinders |
These are the same measures the annual review for this role is built on, so the document you hire against and the document you rate against are measuring one thing.
Reading a resume for this seat
What separates a strong HVAC Install Technician (Commercial) from a plausible one, on paper and in the first ten minutes of a call:
- Brazing with nitrogen purge described as routine rather than as a best practice they have heard of
- Has set equipment by crane and can talk about rigging and roof curb fit
- VRF experience named by manufacturer, because the commissioning differs
Screen for it: 3 questions and what a strong answer contains
A job description tells you what you need. These tell you whether the person in front of you has it. Each one comes with what a strong answer contains, because an interviewer who does not know that is persuaded by fluency, which is exactly what the question was supposed to see past.
How do you purge a line set, and what happens downstream if you skip it?
What a strong answer containsDry nitrogen flowing through the pipe while brazing, at a trickle rather than a blast, so no oxide scale forms on the inside of the joint. Knows the consequence is not cosmetic: that scale breaks loose later, plugs the filter-drier or the metering device, contaminates the oil, and kills a compressor months after the installer has gone.
Follow up with: How do you know the nitrogen is actually flowing through the joint you are brazing and not out the nearest open end?
What do you check on a roof curb before the unit lands?
What a strong answer containsLevel and square, the right curb for that unit rather than the one that was already there, flashing and counter-flashing intact, a continuous gasket, duct openings that line up with the unit rather than nearly, and the deck underneath sound. Checks before the crane arrives, not while the unit is hanging.
Follow up with: What do you do if you find it out of level with the unit already on the hook?
Describe the last VRF system you installed - whose, how many indoor units, and who commissioned it?
What a strong answer containsNames the manufacturer, a real indoor unit count, and who did the commissioning, including whether they were there for it. Knows most VRF warranties depend on factory or certified startup. Someone who helped on one job will go vague on exactly these three details, which is why the question asks for all three.
Follow up with: What is the branch arrangement called on that manufacturer, and what did you have to get right about it?
The mistake this seat invites
Treating install and service as interchangeable. A strong install technician may be a slow diagnostician, and a strong service technician may be uneconomic on a production install crew.
How long this takes to fill
My Trade Talent's median HVAC & mechanical hire took 15 days across 36 searches closed in 2026 year to date, counted as calendar days from our first contact with the candidate to the hire.
Worth writing on the requisition before you post it. The cost of the vacancy runs from the day the seat empties, not from the day you start looking, and the calculator will put a number on it for your billing rate.
Questions employers ask about this role
What does an HVAC Install Technician (Commercial) do?
Sets and connects commercial HVAC equipment on new construction and replacement projects: rooftop units, split systems, VRF branch controllers, ductwork and refrigerant piping. The work is production against a schedule, and the technician is expected to hold rate without cutting corners. The quality of the brazing, the hanger spacing and the condensate detailing decides whether the service department inherits a problem on the unit two years later. The full description below lists 15 essential duties in trade terms, with physical demands and frequencies.
What qualifications does an HVAC Install Technician (Commercial) need?
8 requirements are written as non-negotiable for this seat. The first 3: Three or more years installing commercial HVAC equipment, not residential changeouts only; EPA Section 608 Universal certification; Able to braze copper to copper and copper to brass joints that pass a nitrogen pressure test without rework. A further 7 qualifications are preferred rather than required, which is the distinction that decides whether a good candidate gets screened out by your own posting.
What credentials should I verify before making an offer to an HVAC Install Technician (Commercial)?
4 credentials on this role are either required outright or required where the state requires it: EPA Section 608 Universal, State or local HVAC journeyman or mechanical license, OSHA 10 or OSHA 30 construction and Valid driver's license. Each one has a named place to verify it in the table below. Verify before the offer rather than after; a credential taken on trust at offer is the most expensive line in a job description.
Is an HVAC Install Technician (Commercial) exempt or non-exempt?
Non-exempt — confirm with counsel. FLSA status turns on the duties actually performed rather than the job title, and the duties for this seat are listed below so a classification decision has something to rest on. We are not lawyers and the note here is a starting point for counsel, not a determination.
What should an HVAC Install Technician (Commercial) be paid?
$52,000 to $80,000. My Trade Talent mid-experience band, built from our own engagement history. Experience and region move it; the salary calculator applies both.
How long does it take to hire an HVAC Install Technician (Commercial)?
My Trade Talent's median HVAC & mechanical hire took 15 days across 36 searches closed in 2026 year to date, counted as calendar days from our first contact with the candidate to the hire.
What is the most common hiring mistake in this seat?
Treating install and service as interchangeable. A strong install technician may be a slow diagnostician, and a strong service technician may be uneconomic on a production install crew.
One time
Where should we send it?
Tell us who you are once and every document on this site downloads for you from then on, with no form in the way. We are a recruiting firm: someone may call about the roles you are hiring for.