Skip to main content
Job description

Insulation Worker, Floor/Ceiling/Wall Job Description

Insulation

Installs thermal and acoustic insulation in building assemblies. Places batt, blown, rigid board and spray foam in walls, floors, ceilings and attics, and performs the air sealing and fire-stopping that goes with them. Works to the installation grade, coverage and R-value the drawings and the energy code call for, because on commercial work the assembly gets inspected before it is covered and a missed cavity means opening the wall back up.

15essential duties
8 / 7required / preferred qualifications
6credentials, each with who verifies it
Take this away as a Word document The same description, formatted for a personnel file, with an acknowledgement signature block at the end. The first download asks for your name, company, work email and phone; after that every document here downloads without a form.
Download .docx

What this seat pays

$37,030 to $78,190 BLS 10th to 90th percentile

Federal figures: BLS Occupational Employment and Wage Statistics, May 2025, national, SOC 47-2131. The range is the 10th to 90th percentile and the median is $49,120. It is not adjusted for experience or region, and it is not a My Trade Talent band.

Pay, location and the date prepared are blank in the Word version on purpose. They depend on your market and your margins, and a template that guesses at them is worse than one that leaves them to you. The figure above is here so the guess is at least anchored.

The seat

Reports toInsulation Foreman or Crew Lead
Direct reportsNone (may direct an apprentice or helper)
FLSA statusNon-exempt — confirm with counsel
TradeInsulation
Pay band$37,030 to $78,190 — BLS 10th to 90th percentile

Where the role goes next. Building insulators move to lead and foreman, and spray foam certification raises the work available.

Essential duties (15)

  • Reads the drawings, wall types and energy code details to determine the insulation type, R-value, facing orientation and fire rating required for each assembly before starting.
  • Installs fiberglass and mineral wool batt in wall, floor and ceiling cavities friction-fit and full-width, cut to length rather than folded, and split around wiring, boxes and plumbing instead of compressed behind them.
  • Installs faced batt with the vapor retarder on the correct side for the climate zone and staples or friction-fits it per the manufacturer instructions and the assembly listing.
  • Blows loose-fill fiberglass or cellulose in attics to the specified depth, installs depth markers and baffles at the eaves, dams and covers around access hatches, and keeps the material off recessed fixtures that are not rated for contact.
  • Dense-packs cavities and sloped assemblies to the specified density with netting or fabric where the assembly is not closed, and verifies bag count against the coverage chart.
  • Installs rigid board insulation — polyisocyanurate, XPS, EPS and mineral wool board — on foundations, under slab, on exterior walls as continuous insulation, and at parapets, with the fastener pattern, joint taping and thermal break detailing the specification shows.
  • Applies open-cell and closed-cell spray foam at the correct substrate temperature, in the lift thickness the product data sheet allows, with proper ratio and rig settings, and installs the ignition or thermal barrier where the assembly requires it.
  • Air seals the building envelope: top and bottom plates, rim joists, penetrations for pipe, wire and duct, window and door perimeters, and the transitions between assemblies, using the sealant or foam specified.
  • Installs fire-stopping, draftstopping and safing at rated walls, floors and shafts using listed systems and keeps the documentation of what was installed where.
  • Installs acoustic batt and sound attenuation at demising walls, between floors, and around conference rooms and exam rooms, carried tight to the deck where the detail calls for it.
  • Masks and protects adjacent finishes, windows, equipment and other trades work before spraying, and cleans overspray and trimmings before it cures onto something.
  • Prepares assemblies for inspection, walks them with the inspector or third-party rater, and corrects gaps, compression and missed cavities before the drywall goes on.
  • Operates and maintains the blowing machine, spray rig and hoses: daily checks, pressure and temperature settings, hose care, filter and screen cleaning, and reporting faults rather than running through them.
  • Wears the respirator, suit and eye protection the product requires, enforces reentry times after spray foam work, and keeps unprotected people out of the spray area.
  • Counts and reports material used, square footage installed and hours by area, submits timesheets by the cutoff, and removes bags, wrap and scrap from the site each day.

Qualifications

Required
  • Two or more years installing commercial or multifamily insulation across batt, blown and rigid board work
  • Able to read drawings, wall type schedules and energy code details and determine the required R-value, facing orientation and fire rating
  • Current respirator medical clearance and fit test, and able to work in a respirator with a suit for sustained periods
  • Able to work overhead and above shoulder height, climb ladders and work from lifts and scaffolding
  • Able to work in attics, crawlspaces and confined cavities with limited headroom, in high heat and cold
  • Able to lift and carry up to 50 pounds, including bags of loose-fill material and board bundles
  • Valid driver license and reliable transportation to job sites, with an insurable motor vehicle record if assigned a company vehicle
  • Comfortable with inspection: able to explain and correct installation grade issues when a rater or inspector calls them out
Preferred
  • Spray polyurethane foam experience with rig operation and documented SPFA or manufacturer training
  • Experience passing third-party energy code and above-code program inspections, including Grade I installation standards
  • Fire-stopping experience with listed systems and the documentation that goes with them
  • Blower door and air leakage testing exposure, even as the installer being tested
  • Experience on multifamily or healthcare projects with phased, occupied-building work
  • Aerial lift, scaffold and fall protection training already in hand
  • Bilingual English and Spanish for crew communication on mixed crews

The line between these two columns is the one that costs you candidates. Everything in the preferred column that gets written into a posting as a requirement removes people who could do the job, and in a trade with a shortage that is a self-inflicted wound.

Credentials, and who verifies them

CredentialStatusVerify with
Respirator medical evaluation and annual fit testRequiredOccupational health provider record and the safety manager fit test log
OSHA 10-hour or 30-hour construction trainingRequiredTraining provider or DOL card verified by the safety manager
Spray polyurethane foam installer training such as an SPFA or manufacturer certificationWhere the state requires itThe certifying body or manufacturer training record, held with the crew file
Aerial lift, scissor lift and scaffold user trainingRequiredInternal or third-party trainer records held by the safety manager
Fire-stopping installer training on the listed systems usedPreferredThe manufacturer training record, kept with the submittal file
Driver license with insurable motor vehicle record for assigned driversRequiredHR, through the company insurance carrier MVR check

Verify before an offer rather than after. A credential taken on trust at offer is the most expensive line on this page. We track insulation licensing in 39 states; which of them applies depends on where the work is, not where the company is.

Physical demands

ActivityFrequency
Standing, walking and climbing on framed floors, decking and uneven surfacesConstant (over 2/3 of shift)
Reaching and working above shoulder height to install in ceilings, high walls and to the deckConstant (over 2/3 of shift)
Exposure to fiberglass, cellulose dust, mineral wool and foam chemistry requiring respirator, suit and eye protectionFrequent (1/3 to 2/3 of shift)
Climbing and working from ladders, scaffolding and scissor liftsFrequent (1/3 to 2/3 of shift)
Lifting and carrying up to 50 pounds (loose-fill bags, batt bundles, board stacks, hose)Frequent (1/3 to 2/3 of shift)
Kneeling, crouching, stooping and twisting to fill low cavities, rim joists and floor assembliesFrequent (1/3 to 2/3 of shift)
Repetitive cutting, stapling and trigger use with hand and wrist loadingFrequent (1/3 to 2/3 of shift)
Working in attics and crawlspaces with limited headroom and extreme heat or coldOccasional (under 1/3 of shift)
Crawling and working on hands and knees over joists and in tight cavitiesOccasional (under 1/3 of shift)
Supplied-air or full-face respirator use with a protective suit during spray foam applicationOccasional (under 1/3 of shift)
Working outdoors in heat, cold and wind on exterior continuous insulation and foundation workOccasional (under 1/3 of shift)
Permit-required confined space entry (shafts, vaults, tight interstitial space)Rarely

This is the section a reasonable accommodation decision actually turns on, which is why it is role specific rather than copied across a trade. An estimator sits and walks sites; a screed operator stands beside hot asphalt all day.

Work environment

Commercial, multifamily and institutional construction sites, mostly before drywall: open framing, attics, crawlspaces, exterior walls and foundations. Conditions include airborne fiber and dust, spray foam chemistry and odor, extreme attic heat, cold exterior work, noise and work at height on lifts and scaffold. Hazards are falls through unfinished openings, respiratory and skin exposure, and other trades working in the same cavities. Weather drives the schedule and overtime; occasional phased work in occupied buildings.

Tools and equipment

The company provides all insulation, foam, sealant and fastening material, the blowing machine and spray rig with hoses, ladders, scaffold and lifts, respirators, suits, gloves and eye protection, and crew transportation. The installer owns and maintains hand tools: insulation knives and blades, a tape, straightedge, staplers if personally preferred, utility shears and personal work boots.

How performance is measured

MeasureWhat it captures
Installation grade on inspected assembliesShare of inspected assemblies meeting the Grade I or project-specified installation standard without correction
Energy code and rater inspection pass rateInsulation inspections passed on the first visit without a re-inspection trip
Installed R-value and coverage verifiedAttic depth, bag count and board thickness verified against the specified R-value and coverage chart
Square footage or units completed per crew dayProduction against the planned rate for the assembly type and building
Spray foam yield per setBoard feet achieved per set compared to the product yield, including waste and off-ratio loss
Callbacks for gaps, compression or missed cavitiesReturn trips caused by installation defects after an area was called complete
Material and waste accountabilityMaterial consumed and scrapped against the takeoff, with bags and board counted at the end of each area

These are the same measures the annual review for this role is built on, so the document you hire against and the document you rate against are measuring one thing.

Reading a resume for this seat

What separates a strong Insulation Worker, Floor/Ceiling/Wall from a plausible one, on paper and in the first ten minutes of a call:

  • Air sealing treated as part of the install rather than a separate trade
  • Knows the fire-stopping and draft-stop requirements at penetrations and rated assemblies
  • Spray foam work stated with the training and respiratory protection it requires

Screen for it: 3 questions and what a strong answer contains

A job description tells you what you need. These tell you whether the person in front of you has it. Each one comes with what a strong answer contains, because an interviewer who does not know that is persuaded by fluency, which is exactly what the question was supposed to see past.

How do you insulate and air seal a rim joist so it passes inspection?

What a strong answer contains

Air seals first and insulates second: seals the joint between the sill and the foundation, the subfloor to the rim, and every penetration, then insulates with a material and thickness that meets the code for that assembly. Knows a fibreglass batt stuffed into a rim joist air seals nothing and lets warm air condense on the cold rim. Says what the inspector will look for and leaves it visible until they have.

Follow up with: Why does a batt alone fail in a rim joist?

What do you do where insulation meets a rated wall penetration?

What a strong answer contains

Does not insulate over or into a rated penetration with ordinary material. Knows the fire-stop system is tested as an assembly and that adding insulation to it or packing a sleeve with batt can void the listing. Leaves it to the listed detail and coordinates with whoever owns the fire-stopping. Checks the drawings for where the rated assemblies are rather than finding out at inspection.

Follow up with: Can you pack a rated sleeve with mineral wool? What decides?

What goes wrong with batt installation that still looks finished?

What a strong answer contains

Names the failures that are invisible once the drywall is up: batts compressed behind wiring and pipes instead of split around them, gaps at the top and bottom of the cavity, friction fit that has slipped, batts cut short or forced into a narrow bay, and no air sealing behind them. Says a wall that looks full can perform at a fraction of its rated value, and that this is why the inspection happens before drywall.

Follow up with: How do you insulate a cavity that has a wire running through it?

The mistake this seat invites

Assuming any insulation experience covers it. Compressed or gapped batts pass a glance and fail the blower door, and inspectors increasingly check.

How long this takes to fill

We publish no insulation median of our own yet, so this is the all-trades figure: My Trade Talent's median commercial trades hire took 21 days across 94 searches closed in 2026 year to date, counted as calendar days from our first contact with the candidate to the hire.

Worth writing on the requisition before you post it. The cost of the vacancy runs from the day the seat empties, not from the day you start looking, and the calculator will put a number on it for your billing rate.

Questions employers ask about this role

What does an Insulation Worker, Floor/Ceiling/Wall do?

Installs thermal and acoustic insulation in building assemblies. Places batt, blown, rigid board and spray foam in walls, floors, ceilings and attics, and performs the air sealing and fire-stopping that goes with them. Works to the installation grade, coverage and R-value the drawings and the energy code call for, because on commercial work the assembly gets inspected before it is covered and a missed cavity means opening the wall back up. The full description below lists 15 essential duties in trade terms, with physical demands and frequencies.

What qualifications does an Insulation Worker, Floor/Ceiling/Wall need?

8 requirements are written as non-negotiable for this seat. The first 3: Two or more years installing commercial or multifamily insulation across batt, blown and rigid board work; Able to read drawings, wall type schedules and energy code details and determine the required R-value, facing orientation and fire rating; Current respirator medical clearance and fit test, and able to work in a respirator with a suit for sustained periods. A further 7 qualifications are preferred rather than required, which is the distinction that decides whether a good candidate gets screened out by your own posting.

What credentials should I verify before making an offer to an Insulation Worker, Floor/Ceiling/Wall?

5 credentials on this role are either required outright or required where the state requires it: Respirator medical evaluation and annual fit test, OSHA 10-hour or 30-hour construction training, Spray polyurethane foam installer training such as an SPFA or manufacturer certification, Aerial lift and Driver license with insurable motor vehicle record for assigned drivers. Each one has a named place to verify it in the table below. Verify before the offer rather than after; a credential taken on trust at offer is the most expensive line in a job description.

Is an Insulation Worker, Floor/Ceiling/Wall exempt or non-exempt?

Non-exempt — confirm with counsel. FLSA status turns on the duties actually performed rather than the job title, and the duties for this seat are listed below so a classification decision has something to rest on. We are not lawyers and the note here is a starting point for counsel, not a determination.

What should an Insulation Worker, Floor/Ceiling/Wall be paid?

$37,030 to $78,190. Federal figures: BLS Occupational Employment and Wage Statistics, May 2025, national, SOC 47-2131. The range is the 10th to 90th percentile and the median is $49,120. It is not adjusted for experience or region, and it is not a My Trade Talent band.

How long does it take to hire an Insulation Worker, Floor/Ceiling/Wall?

We publish no insulation median of our own yet, so this is the all-trades figure: My Trade Talent's median commercial trades hire took 21 days across 94 searches closed in 2026 year to date, counted as calendar days from our first contact with the candidate to the hire.

What is the most common hiring mistake in this seat?

Assuming any insulation experience covers it. Compressed or gapped batts pass a glance and fail the blower door, and inspectors increasingly check.

Trade Talk A monthly hiring brief for commercial trades employers

What changed in your trade this month, and what to do about it.

One email a month, and only one. We write a separate issue for every trade we recruit in, so you get yours - not a round-up with your trade buried in paragraph nine. Every issue is written for the person actually doing the hiring.

  • Where wages moved in your trade, by market, and what that does to your next offer
  • How long roles like yours are taking to fill, and where it is getting worse
  • Interview and screening tactics that are landing candidates this month
  • What contractors competing for the same people are doing differently

Built on federal wage data, our own closed searches, and what we hear on the desk every week. Written for employers, not candidates. No pitch, no filler, one click to leave.

Pick your trade. That is the one issue you get, once a month.

One email a month. Your trade and your address, nothing else - we do not sell either, and you can unsubscribe from the bottom of any issue. Read this month's issue for your trade first →